Dimensional stability of stored extended-pour irreversible hydrocolloids materials
DOI:
https://doi.org/10.33448/rsd-v10i16.23338Keywords:
Dimensional accuracy; Irreversible hydrocolloids; Impression materials.Abstract
The purpose of this study was to evaluate the linear dimensional stability of four extended-pour irreversible hydrocolloids (EPIHs). Material and Methods: Five samples per material (Cavex ColorChange, Cavex Orthotrace, Jeltrate Plus, and Orthoprint) were prepared following the manufacturers’ instructions. The samples were prepared using a cylindrical matrix coupled with a nylon-polyamide ring. Two parallel, 25-mm equidistant lines were made on its surface following ANSI/American Dental Association (ADA) Specification 18 for plaster reproducibility and compatibility and Specification 19 for linear dimensional change. The samples were stored in an environment with a relative humidity of 70% (± 3) and temperature of 28°C (± 2). Photo images were obtained using a digital camera to record images for 120 hours, with a standardized distance of 80cm between the lens and the specimen. Adobe Photoshop CS3 software was used for the measurement of the recorded images. The measurements refer to the equivalent distance between the two parallel lines printed on the samples. Data were analyzed using one-way analysis of variance (ANOVA) and Tukey’s test for multiple comparisons between the means of the groups. Results: There was no statistically significant difference (p > 0.05) when EPIHs were compared at the same time of evaluation. Orthoprint, Cavex Orthotrace, and Cavex Colorchange presented with least dimensional stability up to 24 hours (p > 0.05) of storage, followed by Jeltrate Plus (48 hours). Conclusions: Storage of EPIHs for more than 24 hours for Cavex ColorChange and 48 hours for others EPIHs studied produces significant dimensional changes in the impressions stored at a humidity of 70% (± 3) and temperature of 28°C (± 2). Extended storage times produce large dimensional changes.
References
ANSI/ADA Specification 18 (1992). American National Standards Institute/ American Dental Association Council of Scientific Affairs. American Dental Association specification no. 18. Alginate impression materials. Chicago: American Dental Associaton;1992. http://www.ada.org/275.aspx
ANSI/ADA Specification 19 (2004). American National Standards Institute/ American Dental Association Council of Scientific Affairs. American Dental Association specification no. 19 (2000). Dental elastomeric impression materials. http://www.ada.org/275.aspx
ANSI/ADA Specification 4823. International Organization for Standardization. ISO Specification No. 4823:2000. Dentistry - Elastomeric impression materials. 3rd ed.
Bitencourt, S. B., Catanoze, I. A., Silva, E. V. F. D., Turcio, K. H. L., Santos, D. M. D., Brandini, D. A., Goiato, M. C., & Guiotti, A. M. (2021) Extended-pour and conventional alginates: effect of storage time on dimensional accuracy and maintenance of details. Dental Press J Orthod. 30;26(3): e2119251. 10.1590/2177-6709.26.3.e2119251.oar.
Chen, S. Y., Liang, W. M., & Chen, F. N. (2004). Factors affecting the accuracy of elastometric impression materials. J Dent, 32:603-609. 10.1016/j.jdent.2004.04.002.
Cohen, B. I., Pagnillo, M., Deutsch, A. S., & Musikant, B. L. (1995). Dimensional accuracy of three different alginate impression materials. J Prosthodont, 4:195-199. 10.1111/j.1532-849x.1995.tb00340.x.
Dalstra, M., & Melsen, B. (2009). From alginate impressions to digital virtual models: accuracy and reproducibility. J Orthod, 36:36-41. 10.1179/14653120722905.
Donovan, T. E., & Chee, W. W. A review of contemporary impression materials and techniques. Dent Clin North Am 2004;48:445-470. 10.1016/j.cden.2003.12.014.
Erbe, C., Ruf, S., Wostmann, B., & Balkenhol, M. (2012) Dimensional stability of contemporary irreversible hydrocolloids: humidor versus wet tissue storage. J Prosthet Dent, 108:114-122. 10.1016/S0022-3913(12)60117-6.
Eriksson, A., Ockert-Eriksson, G., & Lockowandt, P. (1998) Accuracy of irreversible hydrocolloids (alginates) for fixed prosthodontics. A comparison between irreversible hydrocolloid, reversible hydrocolloid, and addition silicone for use in the syringe-tray technique. Eur J Oral Sci, 106:651-660. 10.1046/j.0909-8836.1998.eos106207.x.
Fellows, C. M., & Thomas, G. A. (2009) Determination of bound and unbound water in dental alginate irreversible hydrocolloid by nuclear magnetic resonance spectroscopy. Dent Mater, 25:486-493. 10.1016/j.dental.2008.10.001.
Garrofé, A. B., Ferrari, B. A., Picca, M., & Kaplan, A. E. Linear Dimensional Stability of Irreversible Hydrocolloid Materials Over Time. Acta Odontol Lainoam 2015 28(3):258-62.
Hiraguchi, H., Nakagawa, H., Kaketani, M., Hirose, H., & Nishiyama, M. (2007). Effects of disinfection of combined agar/alginate impressions on the dimensional accuracy of stone casts. Dent Mater J, 26:457-462. 10.4012/dmj.26.457.
Hiraguchi, H., Nakagawa H., Wakashima, M., Miyanaga, K, Saigo, M., & Nishiyama, M. (2006). Effects of disinfecting alginate impressions on the scratch hardness of stone models. Dent Mater J, 25:172-176. 10.4012/dmj.25.172.
Hiraguchi, H., Nakagawa, H., Wakashima, M, Miyanaga, K., Sakaguchi, S., & Nishiyama, M. (2005) Effect of storage period of alginate impressions following spray with disinfectant solutions on the dimensional accuracy and deformation of stone models. Dent Mater J, 24:36-42. 10.4012/dmj.24.36.
Imbery, T. A., Nehring, J., Janus, C., & Moon, P. C. (2010). Accuracy and dimensional stability of extended-pour and conventional alginate impression materials. J Am Dent Assoc, 141:32-39. 10.14219/jada.archive.2010.0018.
Martin, N., Martin, M. V., & Jedynakiewicz, N. M. (2007)The dimensional stability of dental impression materials following immersion in disinfecting solutions. Dent Mater, 23:760-768. 10.1016/j.dental.2007.01.004.
Nassar, U., Aziz, T., & Flores-Mir, C. (2011) Dimensional stability of irreversible hydrocolloid impression materials as a function of pouring time: a systematic review. J Prosthet Dent, 106:126-133. 10.1016/S0022-3913(11)60108-X.
Patel, R. D., Kattadiyil, M. T., Goodacre, C. J., & Winer, M. S. (2010) An in vitro investigation into the physical properties of irreversible hydrocolloid alternatives. J Prosthet Dent, 104:325-332.
Porrelli, D., Berton, F., Camurri Piloni, A., Kobau, I., Stacchi, C., Di Lenarda, R., & Rizzo, R. (2021). Evaluating the stability of extended-pour alginate impression materials by using an optical scanning and digital method. J Prosthet Dent, 125(1): 189.e1-189.e7. 10.1016/j.prosdent.2020.06.022.
Rohanian, A., Ommati Shabestari, G., Zeighami, S., Samadi, M. J., & Shamshiri, A. R. (2014). Effect of storage time of extended-pour and conventional alginate impressions on dimensional accuracy of casts. J Dent (Tehran), 11(6):655-64.
Sharif, R. A., Abdelaziz, K. M., Alshahrani, N. M., Almutairi, F. S., Alaseri, M. A., Abouzeid, H. L., & Elagib, M. F. A. (2021). The accuracy of gypsum casts obtained from the disinfected extended-pour alginate impressions through prolonged storage times. BMC Oral Health, 9;21(1):296. 10.1186/s12903-021-01649-2.
Todd, J. A., Oesterle, L. J., Newman, S. M., & Shellhart, W. C. (2013). Dimensional changes of extended-pour alginate impression materials. Am J Orthod Dentofacial Orthop, 143:S55-63. 10.1016/j.ajodo.2012.06.016.
Walker, M. P., Burckhard, J., Mitts, D. A., & Williams, K. B. (2010). Dimensional change over time of extended-storage alginate impression materials. Angle Orthod, 80:1110-1115. 10.2319/031510-150.1.
White, A. J., Fallis, D. W., & Vandewalle, K. S. (2010). Analysis of intra-arch and interarch measurements from digital models with 2 impression materials and a modeling process based on cone-beam computed tomography. Am J Orthod Dentofacial Orthop, 137:456 e451-459; discussion 456-457. 10.1016/j.ajodo.2009.09.019.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Rudys Rodolfo de Jesus Tavarez; Etevaldo Matos Maia-Filho; Adriana Santos Malheiros; Oswaldo Serra Santos-Neto; Shelon Cristina Souza Pinto; Flavio das Neves; Leticia Machado Gonçalves; Matheus Coelho Bandeca
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
1) Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
2) Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
3) Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.
