Physical-mechanical properties of panels produced with corn cob particles and different types and contents of adhesives
DOI:
https://doi.org/10.33448/rsd-v10i11.19828Keywords:
Chemical analysis; Physical-mechanical properties; Waste.Abstract
The objective of this research was to evaluate the best type and adequate content of adhesive in low density particleboards produced with corn cob, in addition to the chemical analysis of the particles. The adhesives used were urea-formaldehyde (UF) and phenol-formaldehyde (PF) distributed in three levels (6, 9 and 12%) on the dry mass of the particles and the nominal density was 0.60 g.cm-3. Regarding the water absorption and swelling properties, no significant differences were found between treatments. The mean value calculated for the IE 24 h was 37.07%, being above the minimum limit stipulated by the standard. The modulus of rupture (MOR) and modulus of elasticity (MOE), were influenced by the tested factors. All particleboards met the requirements of the standard norm. For internal adhesion there was a significant effect only for the type of adhesive factor, with the particleboards produced with PF showing the highest means. For the compression property there was no effect of the factors tested. In general, the dimensional stability of the particleboards was below the minimum required by the standard, but the mechanical properties met all requirements.
References
ASTM. (2020). D 1037-12: standard test methods of evaluating properties of wood-base fiber and particles materials. American Society for Testing and Materials (ASTM). West Conshohocken Pennsylvania, EUA. https://www.astm.org/Standards/D1037.htm
ANSI 208.1 (1999). ANSI 208.1: particleboard. American National Standards Institute (ANSI). Gaithersburg, Maryland, Estados Unidos. https://pt.scribd.com/doc/253309972/ANSI-A208-1-1999-PB
Ang, A. F., Ashaari, Z., Lee, S. H., Tahir, P. M. & Halis, R (2019). Lignin-based copolymer adhesives for composite wood panels – A review. Int. J. Adhes 95: 1-12. https://doi.org/10.1016/j.ijadhadh.2019.102408
ABNT. (2003). NBR 11941: madeira: determinação da densidade básica. Associação Brasileira de Normas Técnicas (ABNT).
ABTCP (1974). Métodos de ensaio. Associação Brasileira Técnica de Celulose e Papel (ABTCP).
ABNT (2003). NBR 13999: papel, cartão, pastas celulósicas e madeira - Determinação do resíduo (cinza) após a incineração a 525°C. Associação Brasileira de Normas Técnicas (ABNT). Rio de Janeiro.
CGEE. (2018). Economia do Bambu no Brasil: Tecnologia e Inovação na Cadeia Produtiva – Perspectivas e Desafios. Documento contendo o relatório técnico e analítico do seminário e da oficina de trabalho. Brasília: Centro de Gestão e Estudos Estratégicos (CGEE). https://www.cgee.org.br/document s/10195/734063/3368_Nota+T%C3%A9cnica+Cadeia+Produtiva+do+Bambu.pdf/2118fc55-dd2e-4a0c-994c-55525879fd2b?version=1.0
CEPEA e CNA (2020). Centro de Estudos Avançados em Economia Aplicada e Confederação Nacional da Agricultura e Pecuária. PIB do agronegócio brasileiro de 1996 a 2019. https://www.cepea.esalq.usp.br/br/pib-do-agronegocio-brasileiro.aspx
CS (1966). CS - 236: mat formed wood particle board. San Francisco, California, Estados Unidos.
CONAB (2021). Acompanhamento Da Safra Brasileira De Grãos, v. 8 - Safra 2020/21, n. 6 - Sexto Levantamento, Brasília, p. 1-106.
Cortini, E., Gazzoni, D., Adalberto, A., Mota, M. & Marra, R. (2018). EMBRAPA. Série Desafios Do Agronegócio Brasileiro (NT2) Milho - Caracterização e Desafios Tecnológicos: EMBRAPA, 35 p.
DIN (1982). DIN 52362: testing of wood chipboards, bending test, determination of bending strength, Berlin, Alemanha. https://tienda.aenor.com/norma-din-52362-1-1965-04-554492
Guimarães, I. L., Veloso, M. C. R. A., Lisboa, F. J. N., Mendes, R. F., Mendes, L. M., Farrapo, C. L., Guimarães Junior, J. B. (2019). Aproveitamento do casquilho de soja para a produção de painéis aglomerados convencionais de baixa densidade. Rev. Bras. Ciênc. Agrár 14(2): e5643. https://doi.org/10.5039/agraria.v14i2a5643.
Iwakiri, S. (2005). Painéis de madeira reconstituída. FUPEF.
Iwakiri, S., Andrade, A. S., Cardoso Júnior, A. A., Chipanski, E. R., Prata, J. G. & Adriazola, M. K. O. Produção de painéis aglomerados de alta densificação com uso de resina melamina-ureia-formaladeído. Cerne 11(4): 323-328.
Iwakiri, S., Trianoski, R., Nascimento, C. C., Juizo, C. G. F., Lengowski, E. C., Bilcati, G. K. & Gonçalves, T. (2018). Painéis aglomerados produzidos com seis espécies de madeiras tropicais da Amazônia. Madera y Bosques 24(3): e243371. https://doi.org/10.21829/myb.2018.243371
Iwakiri, V. T., Trianoski, R., Razera, D. L., Iwakiri, S. & Rosa, T. S. (2019). Produção de painel aglomerado estrutural de Mimosa scabrella Benth com resina lignina-fenol-formaldeído. Floram 26(3): e20171006. http://dx.doi.org/10.1590/2179-8087.100617
Kevin, E. I., Ochanya, O. M., Olukemi, A. M., Bwanhot, S. T. N. & Uche, I. (2018). Mechanical Properties of Urea Formaldehyde Particle Board Composite. Am. J. Chem. Eng 2(1): 10-15. http://www.sciencepublishinggroup.com/j/ajcbe
Mendes, R. F., Mendes, L. M., Mendonça, L. L., Guimarães Júnior, J. B. & Mori, F. A. (2014). Qualidade de painéis aglomerados homogêneos produzidos com a madeira de clones de Eucalyptus urophylla. Cerne 20(2). https://doi.org/10.1590/01047760.201420021273
Oliveira, M. L., Souza, L. G. M., Pereira Neto, R. V. & Lima, J. C. (2020). Obtenção e caracterização de um compósito com matriz de resina poliéster e carga de resíduos do sabugo de milho. Res., Soc. Dev 9(12): e32791210849. http://dx.doi.org/10.33448/rsd-v9i12.10849
Pinati, E., Faria, D. L., Mendes, R. F., Mendes, L. M., Protásio, T. P. & Guimarães Júnior, J. B. (2018). Painéis compensados sarrafeados produzidos com Pinus oocarpa, Castilla uleie Acrocarpus fraxinifolius. Ci. Madeira 9(3): 199-208. http://dx.doi.org/10.12953/2177-6830/rcm.v9n3p199-208x
Scatolino, M. V., Silva, D. W., Mendes, R. F. & Mendes, L. M. (2013). Use of maize cob for production of particleboard. Ciênc. e Agrotecnologia 37(4): 330 - 337. https://doi.org/10.1590/S1413-70542013000400006
Silva, D. W., Farrapo, C. L., Pereira, D., Mendes, R. F. & Mendes, L. M. (2015). MDP com partículas de eucalipto e palha de milho. Sci For 43(108): 853-862. https://doi.org/10.18671/scifor.v43n108.10
Silva, D. W., Scatolino, M. V., Prado, N. R. T., Mendes, R. F. & Mendes, L. M. (2018). Addition of Different Proportions of Castor Husk and Pine Wood in Particleboards. Waste and Biomass Valorization 9: 139 - 145. https://doi.org/10.1007/s12649-016-9742-7
Tay, C. C., Hamdan, S. & Osman, M. S. B. Properties of Sago Particleboards Resinated with UF and PF Resin. (2016). Adv. Mater. Sci. Eng 11: 1-12. https://doi.org/10.1155/2016/5323890
Veloso, M. C. R. A., Lopes, F. M., Furtini, A. C. C., Silva, M. G., Mendes, L. M. & Guimarães Júnior, J. B. (2020). Low Density particleboard properties produced with jupati particles and eucalyptus wood. Rev Bras Ciênci Agrár 15(4): e8414. http://www.agraria.pro.br/ojs32/index.php/RBCA/article/view/v15i4a8414
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Marina Resende Ribeiro de Oliveira; Flávia Maria Silva Brito; Luciana Silva Villela; Lourival Marin Mendes; José Benedito Guimarães Junior
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
1) Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
2) Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
3) Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.
