Shear bond strength of resinous cements to Zirconia Katana™ UTML

Authors

DOI:

https://doi.org/10.33448/rsd-v11i3.26497

Keywords:

Cementing; Cementing Agents; Shear strength.

Abstract

The aim of this study is to assess the bond strength of three resinous cements to Zirconia Katana™ UTML (Kuraray Noritake Dental Inc, Miyoshi, Aichi, Japan). Thirty-six blocks of Zirconia were milled and included in polyvynil chloride (PVC) pipes with self-polymerizable acrylic resin. Each sample was polished in a polishing machine, blasted with aluminum particles, cleaned with ultrasound, and dried with compressed air. The cementation was done according to the protocol recommended by the manufacturer. The samples were divided in 3 groups (n=12) according to the resinous cement used: Group R - RelyX™ U200 Automix (3M ESPE, Sumaré, São Paulo, Brazil); Group M - Multilink® N (Ivoclar Vivadent, Schaan, Liechtenstein); and Group P - Panavia™ V5 Paste (Kuraray Noritake Dental Inc, Cotia, São Paulo, Brazil). The shear stress test was performed in EMIC DL2000 (EMIC, São Paulo, SP, Brazil), and failure type was analyzed. Average bond strengths were 5.4 kgf, 5.8 kgf, and 6.68 kgf for groups R1, M1 and P1, respectively. Variance analysis showed no significant difference between groups. None of the groups showed cohesive failure; there was no significant difference in the frequency of mixed and adhesive failure between groups. All three cements showed similar performance in the tests.

References

M ESPE. Passo a Passo de cimentação [online]. https://multimedia.3m.com/mws/media/1228820O/relyx-u200-steps-by-step.pdf

Akay, C., et al. (2016). Effects of Hot Chemical Etching and 10-Metacryloxydecyl Dihydrogen Phosphate (MDP) Monomer on the Bond Strength of Zirconia Ceramics to Resin-Based Cements. J Prosthodont, 26(5),419-23.

Araújo-Júnior, E.N.S., et al. (2020). Hydrothermal degradation methods affect the properties and phase transformation depth of translucent zirconia. J Mech Behav Biomed Mater, 112 (May).

Carvalho, R.F., et al. (2016). Comparison of methanol/hydrochloric, ferric chloride acid versus tribochemical silica coating for adhesion of resin cement to zirconium dioxide. J Adhes Sci Technol, 30(24), 2690-8.

Colombo, M., et al. (2020). Influence of different surface pretreatments on shear bond strength of an adhesive resin cement to various zirconia ceramics. Materials (Basel)., 13(3), 1–13.

Gomes, A.L., et al. (2015). Thermocycling effect on microshear bond strength to zirconia ceramic using Er:YAG and tribochemical silica coating as surface conditioning. Lasers Med Sci., 30(2), 787–95.

Inokoshi, M., et al. (2020). Impact of sandblasting on the flexural strength of highly translucent zirconia. J Mech Behav Biomed Mater, 115,104268.

Kang Y.J., et al. (2020). Effect of low-concentration hydrofluoric acid etching on shear bond strength and biaxial flexural strength after thermocycling. Materials (Basel), 13(6).

Kolakarnprasert, N., et al. (2019). New multi-layered zirconias: Composition, microstructure and translucency. Dent Mater, 35(5), 797-806.

Le M., et al. (2019). Bond strength between MDP-based cement and translucent zirconia. Dent Mater J. 38(3), 480–9.

Lee J.J., et al. (2015). Evaluation of shear bond strength between dual cure resin cement and zirconia ceramic after thermocycling treatment. J Adv Prosthodont. 7(1), 1–7.

Lee, J-H. & Lee, C-H. (2017). Effect of the Surface Treatment Method Using Airborne-Particle Abrasion and Hydrofluoric Acid on the Shear Bond Strength of Resin Cement to Zirconia. Dent J.,5(3), 23.

Lüthy, H., et al. (2006). Effect of thermocycling on bond strength of luting cements to zirconia ceramic. Dental Materials, 22(2), 195–200.

Magalhães, A.P.R., et al. (2020). Yttria-stabilized tetragonal zirconia polycrystal/resin luting agent bond strength: Influence of Titanium dioxide nanotubes addition in both materials. J Prosthodont Res.

Multilink® N. [Bula]. Schaan/Liechtenstein. Ivoclar Vivadent.

Murakami, T., et al. (2017). Zirconia surface modification by a novel zirconia bonding system and its adhesion mechanism. Dent Mater, 33(12),1371–80. https://doi.org/10.1016/j.dental.2017.09.001

Negreiros, W.M., et al. (2017). Effect of cleaning agent, primer application and their combination on the bond strength of a resin cement to two yttrium-tetragonal zirconia polycrystal zirconia ceramics. Eur J Dent, 11, 6-11.

Panavia™ V5 Paste. [Bula]. Cotia/São Paulo, Brasil. Kuraray Noritake Dental Inc.

Pulici Carlos, E., et al. (2017). Surface treatment on shear bond strength. Journal of International Dental and Medical Research , 193-8.

Santos, T.C.V., et al. (2018). Ceramic repairs with resins: silanization protocols. J Dent Health Oral Disord Ther., 9(6), 451‒454.

Sathish, S., et al. (2019). Effect of thermocycling on the micro-tensile bond strength between self-adhesive resin cement and nonphosphate monomer cements on zirconium-oxide ceramics. Indian J Dent Res., 30(1), 73–9.

Sharafeddin, F. & Shoale, S. (2018) Effects of Universal and Conventional MDP Primers on the Shear Bond Strength of Zirconia Ceramic and Nanofilled Composite Resin. J Dent (Shiraz, Iran), 19(1), 48-56.

Yue, X., et al. (2018). Effects of MDP based primers on shear bond strength between resin cement and zirconia. Exp Ther Med., (9), 1–9.

Downloads

Published

22/02/2022

How to Cite

MARTINS, M. C. T. .; FRANCO, A. G. .; CARVALHO, G. A. P. de .; DIAS, S. C. .; MARTINS, C. M. .; MECCA JUNIOR, S.; PEREZ, F. .; RAMOS, E. V. .; FRANCO, A. B. G. . Shear bond strength of resinous cements to Zirconia Katana™ UTML. Research, Society and Development, [S. l.], v. 11, n. 3, p. e31011326497, 2022. DOI: 10.33448/rsd-v11i3.26497. Disponível em: https://rsdjournal.org/index.php/rsd/article/view/26497. Acesso em: 14 jun. 2024.

Issue

Section

Health Sciences