Influence of anatomy on the adhesion performance of four wood species
DOI:
https://doi.org/10.33448/rsd-v9i4.2727Keywords:
Adhesive; Glue line; Shear planes; Shear strength.Abstract
The aim of this study was to evaluate the influence of anatomical characteristics on the adhesion performance of Vatairea sp., Paulownia sp., Aspidosperma populifolium and Tectona grandis wood. Specimens for anatomical, physical and mechanical analyzes were produced from tangentially oriented boards. The treatments were joint glued from pieces of the same anatomical orientation (radial and tangential), evaluated for shear strength and glue line failure. The Vatairea sp wood had the highest specific gravity (0.74 g cm-3) and the Paulownia sp (0.34 g cm-3) wood was smaller. Aspidosperma populifolium species showed the highest shear strength in the glue line in the tangential and radial faces. The anatomical variables with higher influence on the wood adhesion process were pith ray cells and especially fibers that exhibit the greatest correlation with the shear strength of the glue line.
References
Albino, V. C. S.; Mori, F. A.; Mendes, L. M. (2010). Estudo da interface madeira-adesivo de juntas coladas com resorcinol-formaldeído e madeira de Eucalyptus grandis w. Hill ex Maiden. Scientia Forestalis, 38(87), 509-516.
Albino, V. C. S.; Mori, F. A.; Mendes, L. M. (2012). Influência das características anatômicas e do teor de extrativos totais da madeira de Eucalyptus grandis W. Hill ex Maiden na qualidade da colagem. Ciência Florestal, 22(4), 803-811. DOI: http://dx.doi.org/10.5902/198050987561.
Albuquerque, C. E. C.; Latorraca, J. V. F. (2000). Influência das características anatômicas da madeira na penetração e adesão de adesivos. Floresta e Ambiente, 7(1), 158-166.
American Society for Testing and Materials. (2012a). ASTM D-2559: Standard specification for adhesives for bonded structural wood products for use under exterior exposure conditions. West Conshohocken, Annual Book of ASTM Standards, 15p.
American Society for Testing and Materials. (2013). ASTM D-5266: Standard Practice for Estimating the Percentage of Wood Failure in Adhesive Bonded Joints. West Conshohocken, Annual Book of ASTM Standards, 8 p.
American Society for Testing and Materials. (2013). ASTM D-905: Standard Test method for Strength Properties of Adhesive Bonds in Shear by Compression loading. West Conshohocken, Annual Book of ASTM Standards, 5 p.
Associação Brasileira de Normas Técnicas. (1997). NBR 7190: Projeto de estruturas de madeira. Rio de Janeiro, 107 p.
Carneiro, A. C. O; Vital, B. R.; Pereira, F. A. (2007). Adesivos e sua importância na indústria madeireira. In: Oliveira, J. T. S.; Fiedler, N. C.; Nogueira, M. (Ed.). Tecnologias aplicadas ao setor madeireiro ll. Vitória: Gráfica Aquarius, 99-128.
Comissão Panamericana de Normas Técnicas - COPANT. (1974). Método para la descripción de características generales, macroscópicas de las maderas angiospermas dicotiledóneas. Santiago, 30, 1-19.
Frihart, C. R.; Hunt, C. G. (2010). Adhesives with wood materials: bond formation and performance. In: Wood handbook: wood as an engineering material. Madison: USDA, Forest Service, Forest Products Laboratory, 228 -251.
Hernández, W. J. L. (2010). Anatomía y densidad o peso específico de la madera. Revista Forestal Venezolana, 54(1), 67-76.
International Association of Wood Anatomists - IAWA. (1989). List of microscopic features for hardwood identification. IAWA Bulletin, Leiden, 10(3), 219-332.
Lima, C. K. P.; Mori, F. A.; Mendes, L. M.; Carneiro, A. C. O. (2007). Características anatômicas e química da madeira de clones de Eucalyptus e sua influência na colagem. Cerne, 13(2), 123-129.
Lima, I. L.; Garcia, J. N. (2010). Variação da densidade aparente e resistência à compressão paralela às fibras em função da intensidade de desbaste, adubação e posição radial em Eucalyptus grandis Hill ex-Maiden. Revista Árvore, 34(3), 551-559.
Miranda, M. C.; Castelo, P. A. R. (2012). Avaliações anatômicas das fibras da madeira de Parkia gigantocarpa Ducke. Ciência da Madeira, 3(2), 80-88.
Plaster, O. B.; Oliveira, J. T. S.; Abrahão, C. P.; Braz, R. L. (2008). Comportamento de juntas coladas da madeira serrada de Eucalyptus sp. Cerne, 14(3), 251-258.
Tienne, D. L. C.; Nascimento, A. M.; Garcia, R. A.; Silva, D. B. (2011). Qualidade de adesão de juntas de madeira de pinus coladas em condições simuladas de serviço interna e externa. Floresta e Ambiente, 18(1), 16-29. DOI: http://dx.doi.org/10.4322/floram.2011.019.
Vital, B. R.; Maciel, A. S.; Della Lucia, R. M. (2006). Qualidade de juntas coladas com lâminas de madeira oriundas de três regiões do tronco de Eucalyptus grandis, Eucalyptus saligna E Pinus elliottii. Revista Árvore, 30(4), 637-644.
Vito, M. (2013). Estudo das propriedades mecânicas do eucalipto citriodora em condição de incêndio. 112 f. Dissertação (Mestrado em Ciência e Engenharia de Materiais) - Universidade do Extremo Sul Catarinense, Criciúma.
Downloads
Published
How to Cite
Issue
Section
License
Authors who publish with this journal agree to the following terms:
1) Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
2) Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
3) Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.