Polymerization shrinkage of bulk fill resins: integrative review
DOI:
https://doi.org/10.33448/rsd-v12i5.41453Keywords:
Dental materials; Composite resins; Polymerization.Abstract
Introduction: The search for agility in routine procedures in the dental clinic environment has triggered the development of new dental materials, including bulk fill composite resins which, among other properties, have reduced polymerization shrinkage when compared to conventional composite resins. Objective: To observe the polymerization shrinkage of bulk-fill resin when applied in increments between 4 - 5 mm thick, compared to conventional composite resins (2 mm increments). Methodology: This is an integrative review, where articles from the Virtual Health Library (VHL), Scientific Electronic Library Online (Scielo), Brazilian Bibliography of Dentistry (BBO) and Medical Literature Analysis and Retrievel System Online (Medline), in Portuguese and English. The Boolean marker “AND” was used among the descriptors contained in the Health Sciences Descriptors (DeCS) website, namely: Composite resins, polymerization shrinkage, Bulk fill composite resins. Articles that did not meet the objectives of the study were excluded. Results: In view of the review, 13 articles were selected, which indicated lower polymerization contraction of bulkfill resins, requiring a more judicious insertion technique to obtain restorative success. Conclusion: In view of this, it is concluded that composite resins of bulk fill type, due to their greater viscosity and flow in their composition, have similar or less polymerization contraction than conventional composite resins.
References
Aguiar, F. H., Lazzari, C. R., Lima, D. A., Ambrosano, G. M., & Lovadino, J. R. (2005). Effect of light curing tip distance and resin shade on microhardness of a hybrid resin composite. Brazilian oral research, 19(4), 302–306. https://doi.org/10.1590/s1806-83242005000400012
Almeida Junior, L. J. dos S., Lula, E. C. de O., Penha, K. J. de S., Correia, V.S., Magalhães, F. A. C., Lima, D. M., & Firoozmand, L. M. (2018). Polymerization Shrinkage of Bulk Fill Composites and its Correlation with Bond Strength. Brazilian Dental Journal., 29(3), 261-267. https:// doi.org/10.1590/0103-6440201801838.
Arbildo-Vega, H. I., Lapinska, B., Panda, S., Lamas-Lara, C., Khan, A. S., & Lukomska-Szymanska, M. (2020). Clinical Effectiveness of Bulk-Fill and Conventional Resin Composite Restorations: Systematic Review and Meta-Analysis. Polymers, 12(8), 1786. https://doi.org/10.3390/polym12081786.
Besegato, J. F., Jussiani, E. I., Andrello, A. C., Fernandes, R. V., Salomão, F. M., Vicentin, B. L. S., Dezan-Garbelini, C. C., & Hoeppner, M. G. (2019). Effect of light-curing protocols on the mechanical behavior of bulk-fill resin composites. Journal of the mechanical behavior of biomedical materials, 90, 381–387. https://doi.org/10.1016/j.jmbbm.2018.10.026.
Cidreira Boaro, L. C., Pereira Lopes, D., de Souza, A. S. C., Lie Nakano, E., Ayala Perez, M. D., Pfeifer, C. S., & Gonçalves, F. (2019). Clinical performance and chemical-physical properties of bulk fill composites resin -a systematic review and meta-analysis. Dental materials : official publication of the Academy of Dental Materials, 35(10), e249–e264. https://doi.org/10.1016/j.dental.2019.07.007.
Cilingir, A., Ozsoy, A., Mert-Eren, M., Behram, O., Dikmen, B., & Ozcan, M. (2019). Mechanical properties of bulk-fill versus nanohybrid composites: effect of layer thickness and application protocols. Brazilian Dental Science, 2(2)2: 234-242.
Conceição, E. N. (2007). Dentista Saúde e Estética. Artmed, 2, p.356.
Czasch, P., & Ilie, N. (2013). In vitro comparison of mechanical properties and degree of cure of bulk fill composites. Clinical oral investigations, 17(1), 227–235. https://doi.org/10.1007/s00784-012-0702-8
Da Silva Pereira, R. A., de Bragança, G. F., Vilela, A., de Deus, R. A., Miranda, R. R., Veríssimo, C., & Soares, C. J. (2020). Post-gel and Total Shrinkage Stress of Conventional and Bulk-fill Resin Composites in Endodontically-treated Molars. Operative dentistry, 45(5), E217–E226. https://doi.org/10.2341/19-187-L.
Donini, E. D. (2017). Avaliação da resistência de união em reparos entre resinas compostas bulk fill, bulk fill flow e nanoparticulada envelhecidas [Master’s thesis, Universidade Estadual do Oeste do Paraná].
Fernandes, H. G. K., Silva, R., Marinho, M. A. d. S., Oliveira, P. O. d. S., Ribeiro, J. C. R., & Moysés, M. R. (2014). Evolução da resina composta: Revisão da Literatura. Revista da Universidade Vale do Rio Verde, 12, 401-4011.
Gonçalves, F., Campos, L. M. P., Rodrigues-Júnior, E. C., Costa, F. V., Marques, P. A., Francci, C. E., Braga, R. R., & Boaro, L. C. C. (2018). A comparative study of bulk-fill composites: degree of conversion, post-gel shrinkage and cytotoxicity. Brazilian oral research, 32, e17. https://doi.org/10.1590/1807-3107bor-2018.vol32.0017.
Guedes, A. P. A., Oliveira-Reis, B., Catelan, A., Suzuki, T. Y. U., Briso, A. L. F., & Santos, P. H. D. (2018). Mechanical and surface properties analysis of restorative materials submitted to erosive challenges in situ. European journal of dentistry, 12(4), 559–565. https://doi.org/10.4103/ejd.ejd_188_18.
Haugen, H. J., Marovic, D., Par, M., Thieu, M. K. L., Reseland, J. E., & Johnsen, G. F. (2020). Bulk Fill Composites Have Similar Performance to Conventional Dental Composites. International journal of molecular sciences, 21(14), 5136. https://doi.org/10.3390/ijms21145136.
Hayashi, J., Tagami, J., Chan, D., & Sadr, A. (2020). New bulk-fill composite system with high irradiance light polymerization: Integrity and degree of conversion. Dental materials: official publication of the Academy of Dental Materials, 36(12), 1615–1623. https://doi.org/10.1016/j.dental.2020.10.012.
Holanda, L., Neto, E., Costa, F., Costa, E., Neto, V., & Peralta, S. (2017). Desempenho das propriedades físico-mecânicas das resinas bulk-fill: revisão de literatura. Jornada Odontológica dos acadêmicos da Católica, 2(1). http://publicacoesacademicas.unicatolicaquixada.edu.br/index.php/joac/article/view/998.
Ilie, N., & Stark, K. (2015). Effect of different curing protocols on the mechanical properties of low-viscosity bulk-fill composites. Clinical oral investigations, 19(2), 271–279. https://doi.org/10.1007/s00784-014-1262-x.
Jassé, F. F. de A., Alencar, C. de M., Zaniboni, J. F., Silva, A. M., & Campos, E. A. de. (2020). Assessment of Marginal Adaptation Before and After Thermo-Mechanical Loading and Volumetric Shrinkage: Bulk Fill versus Conventional Composite. International journal of odontostomatology, 14(1), 60-66.
Kim, H. J., & Park, S. H. (2014). Measurement of the internal adaptation of resin composites using micro-CT and its correlation with polymerization shrinkage. Operative dentistry, 39(2), E57–E70. https://doi.org/10.2341/12-378-L.
Kim, R. J., Kim, Y. J., Choi, N. S., & Lee, I. B. (2015). Polymerization shrinkage, modulus, and shrinkage stress related to tooth-restoration interfacial debonding in bulk-fill composites. Journal of dentistry, 43(4), 430–439. https://doi.org/10.1016/j.jdent.2015.02.002.
Marovic, D., Tauböck, T. T., Attin, T., Panduric, V., & Tarle, Z. (2015). Monomer conversion and shrinkage force kinetics of low-viscosity bulk-fill resin composites. Acta odontologica Scandinavica, 73(6), 474–480. https://doi.org/10.3109/00016357.2014.992810.
Nobre, D. F. L., & Gomes, C. (2020). Resina composta tipo bulk fill – Um avanço na odontologia restauradora. Cadernos de Odontologia do Unifeso, 2(1), 24-33.
Par, M., Marovic, D., Attin, T., Tarle, Z., & Tauböck, T. T. (2020). Effect of rapid high-intensity light-curing on polymerization shrinkage properties of conventional and bulk-fill composites. Journal of dentistry, 101, 103448. https://doi.org/10.1016/j.jdent.2020.103448.
Pereira, R., Giorgi, M. C. C., Lins, R. B. E., Theobaldo, J. D., Lima, D. A. N. L., Marchi, G. M., & Aguiar, F. H. B. (2018). Physical and photoelastic properties of bulk-fill and conventional composites. Clinical, cosmetic and investigational dentistry, 10, 287–296. https://doi.org/10.2147/CCIDE.S184660.
Rizzante, F. A. P., Duque, J. A., Duarte, M. A. H., Mondelli, R. F. L., Mendonça, G., & Ishikiriama, S. K. (2019). Polymerization shrinkage, microhardness and depth of cure of bulk fill resin composites. Dental materials journal, 38(3), 403–410. https://doi.org/10.4012/dmj.2018-063.
Rodrigues Junior, E. C. (2015). Estudo de propriedade de resinas compostas bulk fill [Master’s thesis, Universidade de São Paulo].
Salem, H. N., Hefnawy, S. M., & Nagi, S. M. (2019). Degree of Conversion and Polymerization Shrinkage of Low Shrinkage Bulk-Fill Resin Composites. Contemporary clinical dentistry, 10(3), 465–470. https://doi.org/10.4103/ccd.ccd_756_18.
Sampaio, C. S., Pizarro, P. G., Atria, P. J., Hirata, R., Giannini, M., & Mahn, E. (2020). Effect of Shortened Light-Curing Modes on Bulk-Fill Resin Composites. Operative dentistry, 45(5), 496–505. https://doi.org/10.2341/19-101-L.
Shibasaki, S., Takamizawa, T., Nojiri, K., Imai, A., Tsujimoto, A., Endo, H., Suzuki, S., Suda, S., Barkmeier, W. W., Latta, M. A., & Miyazaki, M. (2017). Polymerization Behavior and Mechanical Properties of High-Viscosity Bulk Fill and Low Shrinkage Resin Composites. Operative dentistry, 42(6), E177–E187. https://doi.org/10.2341/16-385-L.
Silva, L. N. C., Silveira, C. R., & Carneiro, G. K. M. (2020). Vantagens das resinas bulk fill: revisão da literatura. Revista Saúde Multidisciplinar, 5(1).
Tauböck, T. T., Jäger, F., & Attin, T. (2019). Polymerization shrinkage and shrinkage force kinetics of high- and low-viscosity dimethacrylate- and ormocer-based bulk-fill resin composites. Odontology, 107(1), 103–110. https://doi.org/10.1007/s10266-018-0369-y.
Tusi, S. K., Haja, H., Savadroodbari, M. M., & Fathollahi, M. S. (2022). Comparison of polymerization shrinkage of a new bulk-fill flowable composite with other composites: An in vitro study. Clinical and experimental dental research, 8(6), 1605–1613. https://doi.org/10.1002/cre2.656.
Veloso, S. R. M., Lemos, C. A. A., de Moraes, S. L. D., do Egito Vasconcelos, B. C., Pellizzer, E. P., & Monteiro, G. Q. de M. (2019). Clinical performance of bulk-fill and conventional resin composite restorations in posterior teeth: a systematic review and meta-analysis. Clinical oral investigations, 23(1), 221–233. https://doi.org/10.1007/s00784-018-2429-7.
Yu, P., Xu, Y. X., & Liu, Y. S. (2022). Polymerization shrinkage and shrinkage stress of bulk-fill and non-bulk-fill resin-based composites. Journal of dental sciences, 17(3), 1212–1216. https://doi.org/10.1016/j.jds.2021.12.004.
Yu, P., Yap, A., & Wang, X. Y. (2017). Degree of Conversion and Polymerization Shrinkage of Bulk-Fill Resin-Based Composites. Operative dentistry, 42(1), 82–89. https://doi.org/10.2341/16-027-L.
Zorzin, J., Maier, E., Harre, S., Fey, T., Belli, R., Lohbauer, U., Petschelt, A., & Taschner, M. (2015). Bulk-fill resin composites: polymerization properties and extended light curing. Dental materials official publication of the Academy of Dental Materials, 31(3), 293–301. https://doi.org/10.1016/j.dental.2014.12.010.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2023 Lídia Hana Costa Oliveira; Raylane Gomes Machado; Matheus Araujo Brito Santos Lopes; Daylana Pacheco da Silva; Giselle Maria Ferreira Lima Verde; Lilian Gomes Soares Pires
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
1) Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
2) Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
3) Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.
