Reproducibility of linear measurements performed in dental models from 3D printing

Authors

DOI:

https://doi.org/10.33448/rsd-v10i11.13370

Keywords:

Dental models; Intraoral scanning; Imaging; Three-dimensional printing.

Abstract

This study aimed to assess the reproducibility of linear measurements performed in dental models produced via intraoral scanning and three-dimensional (3D) printing using digital light processing (DLP) and fused deposition modeling (FDM). A sample of 22 participants was selected for this study. Intraoral scanning was performed in each participant with TRIOS™ (3Shape A/S™, Copenhagen, Denmark) device. The digital models were 3D printed using DLP and FDM techniques. Using a caliper, intraoral linear measurements were performed in situ (on the surface of participant’s teeth) and on the 3D printed models. The measurements taken intraoral and on the models were compared using the Intraclass Correlation Coefficient (ICC). The correlation between measurements taken in situ and on DLP models was poor (<0.4), while between in situ and FDM it ranged from poor to satisfactory (<0.75). Generalized linear model showed that the differences did not reach statistically significant levels (p>0.05). According to Bland-Altman approach, the size of measurements did not bias the outcomes. The intraoral scanning and 3D printing techniques used in this study enabled the reproducibility of linear measurements, however, discrete distortions that might be clinically significant occurred.

References

Abduo, J., & Elseyoufi, M. (2018). Accuracy of intraoral scanners: a systematic review of influencing factors. Eur J Prosthodont Restor Dent, 30:101-121. http://doi.org/10.1922/EJPRD_01752Abduo21.

Arakida, T., Kanazaw, A. M., Iwaki, M., Suzuki, T., & Minakuchi, S. (2018). Evaluating the influence of ambient light on scanning trueness, precision, and time of intra oral scanner. J Prothodontic Res, 62:324-329. https://doi.org/10.1016/j.jpor.2017.12.005.

Brown, G. B., Currier, G. F., Kadioglu, O., & Kierl, J. P. (2018). Accuracy of 3-dimensional printed dental models reconstructed from digital intraoral impressions. Am J Orthod Dentofac Orthop, 154:733-739. https://doi.org/10.1016/j.ajodo.2018.06.009

Dawood, A., Marti, B. M., Sauret-Jackson, V., & Darwood, A. (2015). 3D printing in dentistry. Br Dent J, 219:521-529. http://doi.org/10.1038/sj.bdj.2015.914.

Di Ventura, A., Lanteri, V., Farronato, G., Gaffuri, F., Beretta, M., Lanteri, C., & Cossellu, G. (2019). Three-dimensional evaluation of rapid maxillary expansion anchored to primary molars: direct effects on maxillary arch and spontaneous mandibular response. Eur J Pediatr Dent, 20:38-42. http://doi.org/ 10.23804/ejpd.2019.20.01.08.

Dietrich, C. A., Ender, A., Baumgartner, S., & Mehl, A. (2017). A validation study of reconstructed rapid prototyping models produced by two technologies. Angle Orthod, 87:782-787. https://doi.org/10.2319/01091-727.1.

Franco, R. P. A. V., Mobile, R. Z., Filla, C. F. S., Sbalqueiro, R., de Lima, A. A. S., Silva, R. F., Paranhos, L. R., Tanaka, O. M., Turkina, A., & Franco, A. (2019). Morphology of the palate, palatal rugae pattern, and dental arch form in patients with schizophrenia. Special Care Dent, 39(5):464-470. http://doi.org/ 10.1111/scd.12408.

Garino, F., & Garino, G. B. (2002). Comparison of dental arch measurements between stone and digital casts. World J Orthod, 3:250-254. http://doi.org/10.1.1.610.5420

Hirogaki, Y., Sohmura, T., Satoh, H., Takahashi, J., & Takada, K. (2001). Complete 3-D reconstruction of dental cast shape using perceptual grouping. IEEE Trans Med Imag, 20:1093-1101. http://doi.org/10.1109/42.959306.

Kasparova, M., Grafova, L., Dvorak, P., Dostalova, T., Prochazka, A., Eliasova, H., Prusa, J., & Kakawand, S. (2013). Possibility of reconstruction of dental plaster cast from 3D digital study models. Biomed Eng (Online), 12:49. http://doi.org/10.1186/1475-925X-12-49.

Lee, K. Y., Cho, J. W., Chang, N. Y., Chae, J. M., Kang, K. H., Kim, S. C., & Cho, J. H. (2015). Accuracy of three-dimensional printing for manufacturing replica teeth. Korean J Orthod, 45:217-225. http://doi.org/10.4041/kjod.2015.45.5.217.

Mangano, F., Gandolfi, A., Luongo, G., & Logozzo, S. (2017). Intraoral scanners in dentistry: a review of the current literature. BMC Oral Health, 17:149. http://doi.org/10.1186/s12903-017-0442-x.

Mok, S. W., Nizak, R., Fu, S. C., Ho, K. W. K., Qin, L., Saris, D. B. F., Chan, K. M., & Malda, J. (2016). From the printer: Potential of three-dimensional printing for orthopaedic applications. J Orthop Translat, 6:42-49. http://doi.org/10.1016/j.jot.2016.04.003.

Mu, Q., Wang, L., Dunn, C. K., Kuang, X., Duan, F., Zhang, Z., Qi, H. J., & Wang, T. (2017). Digital light processing 3D printing of conductive complex structures. Add Manufac, 18;74-83. https://doi.org/10.1016/j.addma.2017.08.011

Nabbout, F., & Baron, P. (2017). Orthodontics and dental anatomy: three-dimensional scanner contribution. J Int Soc Prev Community Dent, 7:321-328. http://doi.org/10.4103/jispcd.JISPCD_394_17.

Pacheco, A. A. R., Franco, A., Antelo, O. M., Pithon, M. M., & Tanaka, O. M. (2018). Changes in the mandibular arch after rapid maxillary expansion in children: A three-dimensional analysis using digital models. Eur J Gen Dent, 7:47-50. http://doi.org/ 10.4103/ejgd.ejgd_95_18

Pandis, N. (2012). Sample calculations for comparison of 2 means. Am J Orthod Dentofac Orthop, 141:519-521. http://doi.or/10.1016/j.ajodo.2011.12.010.

Rebong, R. E., Stewart, K. T., Utreja, A., Ghoneima, A. A. (2018). Accuracy of three-dimensional dental resin models created by fused deposition modeling, stereolithography, and Polyjet prototype technologies: a comparative study. Angle Orthod, 88:363-369. http://doi.org/10.2319/071117-460.1

Rossini, G., Parrini, S., Castroflorio, T., Deregibus, A., & Debernardi, C. L. (2016). Diagnostic accuracy and measurement sensitivity of digital models for orthodontic purposes: A systematic review. Am J Orthod Dentofac Orthop, 149:161-170. http://dx.doi.org/10.1016/j.ajodo.2015.06.029.

Sanches, J. O., Santos-Pinto, L. A. M., Santos-Pinto, A., Grehs, B., & Jeremis, F. (2013). Comparison of space analysis performed on plaster vs. digital dental casts applying Tanaka and Johnston’s equation. Dental Pres J Orthod, 18:128-133. http://doi.org/10.1590/S2176-94512013000100024.

Schirmer, U. R., & Wiltshire, W. A. (1997). Manual and computer-aided space analysis: a comparative study. Am J Orthod Dentofacial Orthop, 112:676-680.

Szklo, M., & Nieto, F. J. (2018). Epidemiology: beyond the basics. 4th edition. Jones & Bartlett Learning, USA.

Tao, O., Kort-Mascort, J., Lin, Y., Pham, H. M., Charbonneau, A. M., ElKashty, O. A., Kinsella, J. M., & Tran, S. D. (2019). The applications of 3d printing for craniofacial tissue engineering. Micromachines (Basel), 10:480. http://doi.org/10.3390/mi10070480.

Van Noort, R. (2012). The future of dental devices is digital. Dental Mat, 28:3-12.

Vitti, R. P., Da Silva, M. A. B., Consani, R. L. X., & Sinhoreti, M. A. C. (2013). Dimensional accuracy of stone casts made from silicone-based impression materials and three impression techniques. Braz Dent J, 24:498-502. http://doi.org/10.1590/0103-6440201302334.

Wutzl, A., Sinko, K., Shengelia, N., Brozek, W., Watzinger, F., Schicho, K., & Ewers, R. (2009). Examination of dental casts in newborns with bilateral complete cleft lip and palate. Int J Oral Maxillofac Surg, 38:1025-1029. http://doi.org/ 10.1016/j.ijom.2009.04.023

Zhang, H., Yin, L., Liu, Y., Yan, L., Wang, N., Liu, G., An, X., & Liu, B. (2018). Fabrication and accuracy research on 3D printing dental model based on cone beam computed tomography digital modeling. West China J Stomatol, 36:156-161. http://doi.org/10.7518/hxkq.2018.02.008.

Zhang, Z. C., Li, P. L., Chu, F. T., & Shen, G. (2019). Influence of the three-dimensional printing technique and printing layer thickness on model accuracy. J Orofac Orthop, 80;194-204. http://doi.org/ 10.1007/s00056-019-00180-y

Downloads

Published

03/09/2021

How to Cite

MAIA, F. L. M.; FRANCO, A.; AQUINO, D. A. H. de .; OLIVEIRA, L. B. .; JUNQUEIRA, J. L. C. .; OENNING, A. C. C. . Reproducibility of linear measurements performed in dental models from 3D printing. Research, Society and Development, [S. l.], v. 10, n. 11, p. e344101113370, 2021. DOI: 10.33448/rsd-v10i11.13370. Disponível em: https://rsdjournal.org/index.php/rsd/article/view/13370. Acesso em: 16 nov. 2024.

Issue

Vol. 10 No. 11

Section

Health Sciences

License

Copyright (c) 2021 Fernanda Latorre Melgaço Maia; Ademir Franco; Daphne Azambuja Hatschbach de Aquino; Luciana Butini Oliveira; José Luiz Cintra Junqueira; Anne Caroline Costa Oenning

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

Authors who publish with this journal agree to the following terms:

1) Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

2) Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.

3) Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.