Hydrofluoric acid concentration and etching time on bond strength to lithium disilicate glass-ceramic
DOI:
https://doi.org/10.33448/rsd-v10i17.24776Keywords:
Ceramics; Hydrofluoric acid; Cementation; Microshear.Abstract
The objective of this study to evaluate the effect of different HF concentrations and etching times on the microshear bond strength (μSBS) of LD to resin cement. Forty LD sections (8x8 mm) of 3-mm thickness were randomly distributed (n=10) in accordance with the HF concentration (5 or 10%) and surface etching time (20 or 60 sec). The specimens were silanized and received an air-thinned layer of a light-curable adhesive. Six translucent tubes (0.8-mm diameter and 1-mm height) were positioned over each LD section, filled with resin cement and light-cured. After 24 h of storage, the tubes were carefully removed and the specimens were submitted to the μSBS test. The results submitted to a two-way analysis of variance and Sidak post hoc test (α=.05). Representative HF-etched specimens and one non-etched LD specimen were observed under a field-emission scanning electron microscope. The interaction between the HF concentrations and etching times was not significant (p=0.075). No significant differences were observed regarding HF concentrations and etching times (p=0.06 and p=0.059, respectively). Surfaces of specimens etched with 10% HF for 60 sec were found with grooves and microcracks. The μSBS of LD to resin cement was not significantly influenced by different HF concentrations and etching times; however, the LD surface morphology was found considerably modified.
References
Aboushelib, M. N., & Sleem, D. (2014). Microtensile bond strength of lithium disilicate ceramics to resin adhesives. J Adhes Dent, 16(6), 547-552.
Alghazzawi, T. F., Lemons, J., Liu, P. R., Essig, M. E., & Janowski, G. M. (2012). The failure load of CAD/CAM generated zirconia and glass-ceramic laminate veneers with different preparation designs. J Prosthet Dent, 108(6), 386-393.
Bajraktarova-Valjakova, E., Grozdanov, A., Guguvcevski, L., Korunoska-Stevkovska, V., Kapusevska, B., Gigovski, N., Mijoska, A., & Bajraktarova-Misevska, C. (2018). Acid etching as surface treatment method for luting of glass-ceramic restorations, part 1: Acids, application protocol and etching effectiveness. Open Access Maced J Med Sci, 6(3), 568-573.
Blatz, M. B., Sadan, A., & Kern, M. (2003). Resin-ceramic bonding: A review of the literature. J Prosthet Dent, 89(3), 268-274.
Borges, G. A., Sophr, A. M., de Goes, M. F., Sobrinho, C. L., & Chan, D. C. N. (2003). Effect of etching and airborne particle abrasion on the microstructure of different dental ceramics. J Prosthet Dent, 89(5): 479-488.
Bottino, M. A., Snellaert, A., Bergoli, C. D, Özcan, M., Bottino, M. C., & Valandro, L. F. (2015). Effect of ceramic etching protocols on resin bond strength to a feldspar ceramic. Oper Dent, 40(2), 40-46.
Brentel, A. S., Özcan, M., Valandro, L. F., Alarça, L. G., Amaral, R., & Bottino, M. A. (2007). Microtensile bond strength of a resin cement to feldspathic ceramic after different etching and silanization regimens in dry and aged conditions. Dent Mater, 23(11), 1323-1331.
Denry, I., & Kelly, J. R. (2014). Emerging ceramic-based materials for dentistry. J Dent Res, 93(12), 1235-1242.
Edelhoff, D., Prandtner, O., Saeidi Pour, R., Liebermann, A., Stimmelmayr, M., & Güth, J. F. (2018). Anterior restorations: The performance of ceramic veneers. Quintessence Int, 49(2), 89-101.
Gracis, S., Thompson, V. P., Ferencz, J. L., Silva, N.R., & Bonfante, E. A. (2015). A new classification system for all-ceramic and ceramic-like restorative materials. Int J Prosthodont, 28(3), 227-235.
Guarda, G. B., Correr, A. B., Gonçalves, L. S., Costa, A. R., Borges, G. A., Sinhoreti, M. A., & Sobrinho, C. L. (2013). Effects of surface treatments, thermocycling, and cyclic loading on the bond strength of a resin cement bonded to a lithium disilicate glass ceramic. Oper Dent, 38(2), 208-217.
Haddad, M. F., Rocha, E. P., & Assunção, W. G. (2011). Cementation of prosthetic restorations: From conventional cementation to dental bonding concept. J Craniofac Surg, 22(3), 952-958.
Hooshmand, T., Parvizi, S., & Keshvad, A. (2008). Effect of surface acid etching on the biaxial flexural strength of two hot pressed glass ceramics. J Prosthodont, 17(5), 415-419.
Kalavacharla, V. K., Lawson, N. C., Ramp, L. C., & Burgess, J. O. (2015). Influence of etching protocol and silane treatment with a universal adhesive on lithium disilicate bond strength. Oper Dent, 40(4), 372-378.
Lise, D. P., Perdigão, J., Van Ende, A., Zidan, O., & Lopes, G. C. (2015). Microshear bond strength of resin cements to lithium disilicate substrates as a function of surface preparation. Oper Dent, 40(5), 524-532.
Lopes, G. C., Perdigão, J., Baptista, D., & Ballarin, A. (2019). Does a self-etching ceramic primer improve bonding to lithium disilicate ceramics? Bond strengths and FESEM analyses. Oper Dent, 44(2), 210-218.
Mokhtarpour, F., Alaghehmand, H., & Khafri, S. (2017). Effect of hydrofluoric acid surface treatment on microshear bond strength of CAD/CAM ceramics. Electron Physician, 9(10), 5487-5493.
Mörmann, W. H., Stawarczyk, B., Ender, A., Sener, B., Attin, T., & Mehl A. (2013). Wear characteristics of current aesthetic dental restorative CAD/CAM materials: Two-body wear, gloss retention, roughness and martens hardness. J Mech Behav Biomed Mater, 20(1), 113-125.
Ozcan, M., Allahbeickaraghi, A., & Dündar, M. (2012). Possible hazardous effects of hydrofluoric acid and recommendations for treatment approach: A review. Clin Oral Investig, 16(1), 15-23.
Panah, F. G., Rezai, S. M. S., & Ahmadian, L. (2008). The influence of ceramic surface treatments on the micro-shear bond strength of composite resin to IPS Empress 2. J Prosthodont,17(5), 409-414.
Pattanaik, S., & Wadkar, A. P. (2011). Effect of etchant variability on shear bond strength of all ceramic restorations –An in vitro study. J Indian Prosthodont Soc, 11(1), 55-62.
Peumans, M., Valjakova, E. B., De Munck, J., Mishevska, C. B., & Van Meerbeek, B. (2016). Bonding effectiveness of luting composites to different CAD/CAM materials. J Adhes Dent, 18(4), 289-302.
Posritong, S., Borges, A. L., Chua, T. M., Eckert, G. J., Bottino, M. A., & Bottino, M. C. (2013). The impact of hydrofluoric acid etching followed by unfilled resin on the biaxial strength of a glass-ceramic. Dent Mater, 29(11), 281- 290.
Prochnow, C., Venturini, A. B., Grasel, R., Bottino, M. C., & Valandro, L. F. (2017). Effect of etching with distinct hydrofluoric acid concentrations on the flexural strength of a lithium disilicate-based glass ceramic. Biomater J Biomed Mater Res B Appl, 105(4), 885-891.
Puppin-Rontani, J., Sundfeld, D., Costa, A. R., Correr, A. B., Puppin-Rontani, R. M., Borges, G. A., Sinhoreti, M., & Correr-Sobrinho, L. (2017). Effect of hydrofluoric acid concentration and etching time on bond strength to lithium disilicate glass ceramic. Oper Dent, 42(6), 606-615.
Ramakrishnaiah, R., Alkheraif, A. A., Divakar, D. D., Matinlinna, J. P., & Vallittu, P. K. (2016). The effect of hydrofluoric acid etching duration on the surface micromorphology, roughness, and wettability of dental ceramics. Int J Mol Sci, 17(6), 822.
Santos, M. J. M. C., Costa, M. D., Rubo, J. H., Pegoraro, L.F., & Santos, Jr. G. C. (2015). Current all-ceramic systems in dentistry: a review. Compend Contin Educ Dent, 36(1), 38-40.
Shimada, Y., Yamaguchi, S., & Tagami, J. (2002). Micro-shear bond strength of dual-cured resin cement to glass ceramics. Dent Mat, 18(5), 380-388.
Sundfeld, D., Correr-Sobrinho, L., Pini, N. I., Costa, A. R., Sundfeld, R. H., Pfeifer, C. S., Martins, L. R. (2016). The effect of hydrofluoric acid concentration and heat on the bonding to lithium disilicate glass ceramic. Braz Dent J, 27(6), 727-733.
Sundfeld, D., Palialol, A. R. M., Fugolin, A. P. P., Ambrosano, G. M. B., Sobrinho, C. L., Martins, L. R. M., Pfeifer, C. S. (2018). The effect of hydrofluoric acid and resin cement formulation on the bond strength to lithium disilicate ceramic. Braz Oral Res, 32: e43.
Sundfeld Neto, D., Naves, L. Z., Costa, A. R., Correr, A. B., Consani, S., Borges, G. A., & Sobrinho, C. L. (2015). The effect of hydrofluoric acid concentration on the bond strength and morphology of the surface and interface of glass ceramics to a resin cement. Oper Dent, 40(5), 470-479.
Trakyali, G., Malkondu, Ö., Kazazoglu, E., & Arun, T. (2009). Effects of different silanes and acid concentrations on bond strength of brackets to porcelain surfaces. Eur J Orthod, 31(4), 402-406.
Venturini, A. B., Prochnow, C., Rambo, D., Gundel, A., & Valandro, L. F. (2015). Effect of hydrofluoridric acid concentration on resin adhesion to a feldspathic ceramic. J Adhes Dent, 17(4), 313-320.
Zogheib, L. V., Della Bona, A., Kimpara, E. T., & Mccabe, J. F. (2011). Effect of hydrofluoric acid etching duration on the roughness and flexural strength of a lithium disilicate-based glass ceramic. Braz Dent J, 22(1), 45-50.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Roberta Pinto Pereira; Renan Dias Carvalho; Carolina Mayumi Cavalcanti Taguchi; Sylvio Monteiro Jr; Renata Gondo
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
1) Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
2) Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
3) Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.