Physicomechanical characterization and wood machining from 10 12-year-old Hevea progeny clones with potential for furniture
DOI:
https://doi.org/10.33448/rsd-v10i17.24239Keywords:
Rubber tree; Wood quality; Wood properties.Abstract
The objective of this work was to evaluate the physical, mechanical, and wood machining properties of 10 clonal progenies with 12 years of age aiming to produce furniture. A total of 10 progenies and three trees per progenies were used, totalling 30 trees analyzed. The basic density ranged from 0.404 g.cm-3 (IAC 301) to 0.495 g.cm-3 (IAC 326), being it considered a light wood. The anisotropy coefficient values ranged from 1.05 (IAC 40) to 1.68 (PB 330) considered low to medium dimensional instability allowing the use of wood to produce furniture with low dimensional movements. In the compression test most clones fall under class C30. For MOR and MOE, it was observed greater values for IAC 326 (11666 MPa) and GT1 (9575 MPa). In wood machining tests, slightly raised large and few defects on the surface, being them considered easy to work. The results obtained for Hevea brasiliensis, 12 years old, allow us to affirm that wood from a younger age is an alternative for furniture production and will consequently contribute to the reduction of the exploitation and degradation of native forests in Brazil for this purpose.
References
Aguilera, A. (2011). Surface roughness evaluation in medium density fibreboard rip sawing. European Journal of Wood and Wood Products, 69(3),489–493. doi: 10.1007/s00107-010-0481-3
American Society for Testing and Materials-ASTM. (1995). 1666-87. Standard Method for conducting machining tests of wood and wood base materials. 17p.
Associação Brasileira de Normas Técnicas-ABNT. (1997). NBR 7190. Projeto de estruturas de madeira. 1,6.
Associação Brasileira de Normas Técnicas-ABNT. (2003). NBR 11941. Determinação da densidade básica. 1,6.
Bandeira, C. T. (2015). Brazilian forestry legislation and to combat deforestation government policies in the amazon (Brazilian amazon). Ambiente e Sociedade, 4, 215-234. https://doi.org/10.1590/1809-4422ASOC1216V1842015
Braz, R. L., Oliveira, J. T. S., Rodrigues, B. P., & Arantes, M. D. C. (2013). Propriedades físicas e mecânicas da madeira de Toona ciliata em diferentes idades. Floresta, 43(4), 663-670.doi: http://dx.doi.org/10.5380/rf.v43i4.30559
Cáceres, C. B., Hernández, R. E., Fortin, Y., & Beaudoin, M. (2017). Wood density and extractive content variation among Japanese larch (Larix kaempferi, [Lamb.] Carr.). Wood Fiber Science, 49, 363-372. doi: 10.1080 / 17480272.2017.1327460
Dhamodaram, T. K. (2008). Status of rubber Wood processing and utilization in India: a country report. In: Promotion of Rubberwood Processing Technology in the Asia-Pacific Region, Haikou, 17-33pp.
Dias Jr, A. F., Santos, P. V., Pace, J. H. C., Carvalho, A. M., & Latorraca, J. V. F. (2013). Caracterização da madeira de quatro espécies florestais para usos em movelaria. Brazilian Journal Wood Science,4(1),93-107. Doi: org/10.15210/cmad.v4i1.4048
Eleotério, J. R., Reichert, D., Hornburg, K. F., & Meneguelli, I. (2014). Massa específica e retratibilidade da madeira de seis espécies de eucaliptos cultivados no litoral de Santa Catarina. Floresta, 45(2), 329-336. Doi: 10.5380/rf.v45i2.34699
Eufrade Jr, H. J., Ohto, J.M., Silva, L.L., Palma, H.A.L., & Ballarin, A.W. (2015). Potential of rubberwood (Hevea brasiliensis) for structural use after the period of latex extraction: a case study in Brazil. Journal Wood Science, 61,384-390. doi:10.1007/s10086-015-1478-7
Foelkel, C. (2014). Espécies de importância Florestal para a Ibero América. Pinus letter, 41, 1-27.
Fonseca, M. A. (2016). Análise do processo de lixamento na madeira de Pinus elliottii e Eucalyptus saligna. Dissertação de Mestrado.
Glass, S. V. & Zelinka, S. L. (2010). Moisture relations and physical properties of wood. In. Wood handbook: wood as an engineering material. Chap. 4. Department of Agriculture, Forest Products Laboratory. Madison, United States of America.
Gonçalves, F. G. G., Oliveira, J. T. S., Della Lucia, R. M., & Sartório, R. C. (2009). Estudo de algumas propriedades mecânicas da madeira de híbrido clonas de Eucalyptus urophylla x Eucalyptus grandis, Revista Árvore, 33 (3), 501-509.
Gonçalves, P. D. S. (2001). Manual de Heveicultura para o estado de São Paulo. Série tecnológica. Instituto Agronômico de Campinas.https://books.google.com.br/books/about/Manual_de_heveicultura_para_o_Estado_de.html?id=_nboZwEACAAJ&redir_esc=y
Hashim, R., How, L. S., Kumar, R. N., & Sulaiman, O. (2005). Some of the properties of flame-retardant medium density fiberboard made from rubberwood and recycled containers containing aluminum trihydroxide. Bioresourse Technology, 96,1826–1831. doi.org/10.1016/j.biortech.2005.01.023
Instituto do Homem e Meio Ambiente da Amazônia- Imazon (2002). Consumo de madeira no mercado interno brasileiro e promoção da certificação florestal. 41 (1). https://imazon.org.br/PDFimazon/Portugues/livretos/acertando-o-alvo-consumo-de-madeira-no-mercado.pdf
Industria Brasileira de árvores- IBA. (2020). Relatório anual 2019. Série Online.
Killman, W. & Hong, L. T. (2000). Rubberwood - the success of an agricultural by product. Unasylva ,51,66-72.
Kretschmann, D. E. (2010). Mechanical properties of wood. Wood handbook: wood as an engineering material chapter 5. Department of Agriculture, Forest Products Laboratory. Madison, United States of America.
Lahr, F. A. R., Christoforo, A. L., Varanda, L. D., Chaud, E., Araújo,V. A. A., & Branco, L. A. M. (2017). Shear and longitudinal modulus of elasticity in wood: relations based on static beding test. Acta Scientiarum Technology, 39,433-437. doi: doi.org/10.4025/actascitechnol.v39i4.30512
Lima, I. L., Bergarmo, R., Bermurdez, K. R., Moraes, M. L. T., & Garcia, J. N. (2020). Caracterization of mechanical properties of wood of clones of Hevea brasiliensis (Willd. Ex Adr.). Scientia Forestalis, 48, 1-12. https://doi.org/10.18671/scifor.v48n125.04
Lucas Filho, F.C. & Boehls, L. (2007). Usinagem da madeira e industria de móveis. Revista da madeira. 108,56-59.
Menucelli, J. R., Amorim, E. P., Freitas, M. L. M., Zanata, M., Cambuim, J., Moraes, M. L. T., Yamaji, F. M., Junior Silva, F. G., & Longui, E. L. (2019). Potencial of Hevea brasiliensis clones, Eucalytus pellita and Eucalyptus tereticornis Wood as Raw Materials for bioenergy Based on Heating Value. Bioenergy Research, 12,992- 999. doi.org/10.1007/s12155-019-10041-6
Mori, C .L. S., Mori, F. A., Mendes, L. M., & Silva, J. R. M. (2003). Caracterização da madeira de angico vermelho (Anadenanthera peregrina (Benth.) Spreng para confecção de móveis. Brasil Florestal,1,29–36.
Moya, R., Salas, C., Berrocal, A., & Valverde, J. C. (2015). Evalution of chemical compositions air dry, preservation and workanility of eight fastgrowing plantation species in Costa Rica. Maderas y Bosques, 21, 31-47.
Naji, H. R., Sahri, M. H., Nobuchi, T., & Bakar, E. D. (2012). Clonal and planting density effects on some properties of Rubber wood (Hevea brasiliensis Muell. Arg.). Bioresosurces,7,189-202. doi:10.15376/biores.7.1.0189-0202
Okino, E. Y. A. (2009). Uso das madeiras de seringueira, pinus e cipreste na fabricação de chapas OSB. Floresta, 39,457-468.
Oliveira, J. T. S., Filho, M. T., & Fiedler, N. C. (2010). Evaluation of the retratibility in seven eucalypt species. Árvore, 34, 929-936. doi.org/10.1590/S0100-67622010000500018
Ramos, L. M. A., Latorraca, J. V. F., Neto, T. C., Martins, L. S., & Severo, E. T. D. (2016). Anatomical Characterization of tension wood in Hevea brasiliensis (Will.ex.A.Juss.). Mull. Arg. Revista Árvore, 40, 1099-1107. https://doi.org/10.1590/0100-67622016000600016
Santana, M. A. E., Eiras, K. M. M., & Pastore, T. C. M. (2001). Avaliação da madeira de quartos clones de Hevea brasiliensis por meio de sua caracterização físico-mecânica. Brasil Florestal, 70,61-68.
Santos, V. B., Santos, L. C. S., Santana, J. C. S., Caetano, M. M., & Silva, G. C. (2017). propriedades físicas de espécies utilizadas no setor da construção civil em Vitória da conquista-BA. Enciclospédia Biosfera,14 (25), 1084-1094.
Santos, H. G., Jacomine, P. K. T., Anjos, L. H. C., Oliveira, V. A., Oliveira, J. B., Coelho, M. R., Lumbrelas, J. F., Cunha, T. J. F., & Almeida, J. A. (2018). Sistema Brasileiro de Classificação de Solos.
Scaloppi-Junior, E. J., Freitas, R. S., and Gonçalves, P. S. (2017). O agronômico: Boletim técnico informativo do Instituto Agronômico de Campinas, 70, 56-61.
Sebrae- Serviço de Apoio às Micro e Pequenas Empresas. (2018). Gestão de custos em Seringais.
Silva, C. J., Vale, A. T., & Miguel, E. P. (2015). Densidade básica da madeira de espécies árboreas de cerradão no estado de Tocantins. Pesquisa Florestal Brasileira, 35,63-75. doi.org/10.4336/2015.pfb.35.82.822
Silva, J. R. M., Lima, J. T., & Trugilho, P. F. (2007). Usinagem da madeira de Eucalyptus grandis em diferentes regiões da medula à casca. Floresta, 13,25-31. doi.org/10.1590/S0100-67622005000300016
Silveira, L. H. C., Rezende, A. V., & Vale, A. T. (2013). Teor de umidade e densidade básica da madeira de nove espécies comerciais amazônicas. Acta Amazônica, 43,179-184.doi.org/10.1590/S0044-59672013000200007
Taques, A. C. & Arruda, T. P. M. (2016). Usinagem da madeira de Angelim pedra (Hymenolobium petraeum). Revista de Ciências Agroambientais, 14,97-103.
Teoh, Y. P., Don, M. M., & Salmiah, U. (2011). Assessment of the properties, utilization, and preservation of rubberwood (Hevea brasiliensis): a case study in Malaysia. Journal of wood Science, 57,255-266. doi.org/10.1007/s10086-011-1173-2
Tenorio, C., Moya, R., Salas, C., & Berrocal, A. (2016). Evaluation of wood properties from six native species of forest plantations in Costa Rica. Bosque, 37, 71-84. Doi: 10.4067/S0717-92002016000100008
Trianoski, R., Matos, J. L. M., Iwakiri, S., & Prata, J. G. (2013). Avaliação da estabilidade dimensional de Pinus tropicais. Revista Floresta e Ambiente, 20 (3), 398-406. Doi: http://dx.doi.org/10.4322/floram.2012.071
Vahid, N. & Cool, J. (2018). A review on wood machining: characterization, optimization, and monitoring of the sawing process. Wood Material Science & Engineering, 15,1-16. doi.org/10.1080/17480272.2018.1465465
Varasquim, F. M. F. A., Alves, M. C. S., Gonçalves, M. T. T., Santiago, L. F. F., & De Souza, A. J. D. (2012). Influence of belt speed, grit sizes and pressure on the sanding of Eucalyptus grandis wood. Cerne, 18, 2. https://doi.org/10.1590/S0104-77602012000200007
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Erick Phelipe Amorim; Juraci de Andrade Barbosa; Adriano Wagner Ballarin; Miguel Luiz Menezes de Freitas; Mario Luiz Teixeira de Moraes; José Cambuim; Marcela Aparecida de Moraes; Paulo de Souza Gonçalves; Eduardo Luiz Longui
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
1) Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
2) Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
3) Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.
