Evaluación del posicionamiento del canal mandibular en prototipos biomédicos estereolitográficos

Autores/as

DOI:

https://doi.org/10.33448/rsd-v13i1.44735

Palabras clave:

Anatomía; Estereolitografía; Mandíbula; Nervio mandibular; Tomografía.

Resumen

Objetivo: El objetivo de este estudio fue evaluar la precisión del posicionamiento de los conductos mandibulares en prototipos estereolitográficos comparándolos con las mandíbulas humanas secas sobre las que se realizaron. Material y métodos: 10 mandíbulas humanas (20 conductos mandibulares) fueron sometidas a una tomografía computerizada y reproducidas en biomodelos estereolitográficos transparentes con los conductos mandibulares visibles para poder tomar medidas lineales entre puntos predeterminados y compararlas. Para analizar los datos se utilizó la prueba t de muestras pareadas, y los valores p < 0,05 se consideraron estadísticamente significativos. Resultados: Los resultados obtenidos mostraron que existe una diferencia relativa estadísticamente significativa de aproximadamente el 10,21% entre las medidas obtenidas en mandíbulas secas y biomodelos. Por último, se evaluó la similitud y la variabilidad de las mediciones intra e interexaminadores y se observó una gran concordancia en ambos casos, lo que demuestra la reproducibilidad del método utilizado. Conclusión: Son necesarios más estudios antes de que el canal mandibular de los prototipos estereolitográficos pueda utilizarse como parámetro para uso clínico.

Biografía del autor/a

Andressa Ferreira Martins, Universidade Paulista

Graduated in Dentistry from Universidade Paulista - Goiânia/GO (2013-2017); Postgraduate degree in implantology from ABO-GO (2017-2019), accredited by Faculdade Herrero; Improvement in minor oral surgery - UNIP-Goiânia (2016); Improvement in dental radiology - UNIP-Goiânia (2016); Advanced training in bone anchors (All-on-Four Surgery) (2021); Advanced training in guided bone regeneration (2021); Advanced training in guided surgery (2022); Advanced residency in zygomatic implants - ITC Brasilia (2022); Member of the International Time of Implantology (ITI);

Igor Ednardo Santos Cézar, Escola Baiana de Medicina e Saúde Pública

Graduated in Dentistry from the Federal University of Sergipe in 2002; Specialist in Prosthodontics and Implant Dentistry from the Brazilian Dental Association of Sergipe (2005) and Bahia (2010) respectively; and Master in Implant Dentistry from the Bahiana School of Medicine and Public Health (2013). He has taught as part of the teaching team for the Lato Senso (specialization) courses in Prosthodontics and Implant Dentistry at ABO-SE and Tiradentes University (UNIT), and as a guest lecturer in Occlusion and Integrated Practice at the Federal University of Sergipe. He currently teaches on the undergraduate Dentistry course at UNIAGES and on the specialization course in Prosthodontics at CIA. She also has the experience of having worked as a team member in the government's Family Health program and as an alternate member of the Sergipe State Dental Surgeons' Union. She has been working in private practice since graduating and today, more specifically, in the sub-areas of aesthetics, implantology, prosthetics and TMD. He has presented and supervised scientific papers at national congresses and at the end of specialization courses, as well as taking part in at least a dozen examining boards for Lato Senso course conclusion papers. He has published scientific articles, including a book chapter in the field of implant dentistry.

Lívia Prates Soares, Escola Baiana de Medicina e Saúde Pública

Dr. Lívia Prates has a degree in Dentistry from the Federal University of Bahia (2002), is a Specialist in Oral and Maxillofacial Surgery and Traumatology and a Master's Degree in Dentistry in the area of Oral and Maxillofacial Surgery and Traumatology from the Pontifical Catholic University of Rio Grande do Sul (2005), completed her PhD in Oral and Maxillofacial Surgery and Traumatology from the Postgraduate Program in Dentistry at the Pontifical Catholic University of Rio Grande do Sul (2011). Since 2020, she has also been a Specialist in Implant Dentistry at the Bahiana Foundation for the Development of Sciences. Since 2002, she has taught Oral Anatomy, General Physiology, Surgical Propaedeutics 1 and 2, Surgery 1, Surgery 2 and Surgery 3 at the following dental schools: Federal University of Bahia, Metropolitan Education Union (UNIME), Bahiana School of Medicine and Public Health (EBMSP). She was a preceptor and vice-coordinator of the Residency and Specialization in Oral and Maxillofacial Surgery and Traumatology based at the Roberto Santos General Hospital and EBMSP for 10 years. Since 2016, she has been on duty at SAMU during a multi-victim event (CARNAVAL - SSA/BA), treating the injured and traumatized. She was coordinator of the NEOBA Oral Surgery Improvement Course. Professor of the Specialization Course in Orthodontics - NEOBA/IPEO, responsible for Orthognathic Surgery and Head and Neck Anatomy. She is a member of the clinical staff at Hospital Português da Bahia/ SSA-BA and Hospital Santo Amaro/SSA-BA; as well as being registered as an oral and maxillofacial surgeon at various hospitals in Bahia. Today, she coordinates the Minor Oral Surgery training course at the Peres Institute - GO, and teaches orthodontics courses at the Peres Institute. Clinical staff at Hospital do Coração de Goiás, Hospital Jacob Facuri and HUGOL. She is also a registered oral and maxillofacial surgeon at several hospitals in Goiânia. CEO and founding partner of ICON (Instituto de Cirurgia Ortognatica do Nordeste) and MIT (Maxillofacial International Team).

Maylon Luciano Garcia Barbosa, São Leopoldo Mandic

He holds a degree in Dentistry from Faculdades Integradas da União Educacional do Planalto Central (2015) and a degree in Physiotherapy from Universidade Paulista (2011). Master's degree (ongoing) in Oral and Maxillofacial Traumatology Surgery at São Leopoldo Mandic São Paulo, Specialist in Oral and Maxillofacial Traumatology Surgery, Specialist in Implant Dentistry, Currently responsible for technical matters at IBRO Odontologia, Professor at Instituto Peres.

Citas

Akhila, A., Nandakishore, B., Miriam, M., Anil, S., Abhinav, M., & Fares, A. (2019). Rapid prototyping: An innovative technique in prosthodontics. International Journal of Preventive and Clinical Dental Research, 6(2), 46. https://doi.org/10.4103/inpc.inpc_16_19

Asaumi, J., Kawai, N., Honda, Y., Shigehara, H., Wakasa, T., & Kishi, K. (2001). Comparison of three-dimensional computed tomography with rapid prototype models in the management of coronoid hyperplasia. Dento Maxillo Facial Radiology, 30(6), 330–335. https://doi.org/10.1038/sj/dmfr/4600646

Bioparts – Prototipagem Biomédica. (n.d.). https://bioparts.com.br/?gclid=EAIaIQobChMIga3Gq_KcgwMVqFhIAB2wTQS7EAAYASAAEgIO5vD_BwE

Bomfim, R. T. (2017). Avaliação da acurácia de reconstruções panorâmicas geradas a partir de tomografia computadorizada: estudo experimental in vitro com mandíbulas secas humanas. Repositoriohml.ufba.br. https://repositoriohml.ufba.br/handle/ri/23513

Chilvarquer, I., Chilvarquer, L. W., Hayek, J. E., & Pinto, A. V. de S. (2004). A estereolitografia na Implantodontia avançada: conceitos, indicações e usos. ImplantNews, 69–72. https://pesquisa.bvsalud.org/portal/resource/pt/lil-405747

Choi, J.-Y., Choi, J.-H., Kim, N.-K., Kim, Y., Lee, J.-K., Kim, M.-K., Lee, J.-H., & Kim, M.-J. (2002). Analysis of errors in medical rapid prototyping models. International Journal of Oral and Maxillofacial Surgery, 31(1), 23–32. https://doi.org/10.1054/ijom.2000.0135

Freitas, S. A. P., Costa, P. M., & Ribeiro, R. C. (2010). The Use of biomedic prototyping in dentistry Uso da prototipagem biomédica em Odontologia. Odontol. Clín.-Cient, 9(3), 223–227. http://revodonto.bvsalud.org/pdf/occ/v9n3/a08v9n3.pdf

Giacomo, G. A. P. D., Cury, P. R., Araujo, N. S. de, Sendyk, W. R., & Sendyk, C. L. (2005). Clinical Application of Stereolithographic Surgical Guides for Implant Placement: Preliminary Results. Journal of Periodontology, 76(4), 503–507. https://doi.org/10.1902/jop.2005.76.4.503

Gupta, A., Kumar, S., Singh, S. K., Kumar, A., Gupta, A., & Mehta, P. (2021). Assessment of Anterior Loop of Inferior Alveolar Nerve and Its Anatomic Variations with Age, Gender, and Dentition Status in Indian Population: A CBCT Study. International Journal of Dentistry, 2021, 1–6. https://doi.org/10.1155/2021/1813603

Hm, A., M, S., Ma, A., M, S., & Ma, A. (2012, September 1). Applications of CBCT in Dental Practice: A Review of the Literature. General Dentistry. https://pubmed.ncbi.nlm.nih.gov/23032226/

Ibrahim, D., Broilo, T. L., Heitz, C., de Oliveira, M. G., de Oliveira, H. W., Nobre, S. M. W., dos Santos Filho, J. H. G., & Silva, D. N. (2009). Dimensional error of selective laser sintering, three-dimensional printing and PolyJetTM models in the reproduction of mandibular anatomy. Journal of Cranio-Maxillofacial Surgery, 37(3), 167–173. https://doi.org/10.1016/j.jcms.2008.10.008

ijsr, K. S. L., Snehal V. Kharwade, Jaykumar R. Gade, International Journal of Science and Research (IJSR). (n.d.). Rapid Prototyping: A Modernistic Era in Prosthodontics, IJSR, Call for Papers, Online Journal. International Journal of Science and Research (IJSR). Retrieved December 20, 2023, from https://www.ijsr.net/getabstract.php?paperid=SR20831195638

Jandyal, A., Chaturvedi, I., Wazir, I., Raina, A., & Ul Haq, M. I. (2022). 3D printing – A review of processes, materials and applications in industry 4.0. Sustainable Operations and Computers, 3, 33–42. https://doi.org/10.1016/j.susoc.2021.09.004

Kragskov, J., Sindet-Pedersen, S., Gyldensted, C., & Jensen, K. L. (1996). A comparison of three-dimensional computed tomography scans and stereolithographic models for evaluation of craniofacial anomalies. Journal of Oral and Maxillofacial Surgery: Official Journal of the American Association of Oral and Maxillofacial Surgeons, 54(4), 402–411; discussion 411-412. https://doi.org/10.1016/s0278-2391(96)90109-3

Kumar, S. R., Patil, P. G., Choy, C. S., & Veerakumarasivam, A. (2020). The location of the inferior alveolar nerve in the malaysian population: Implications for dental implant planning. Indian Journal of Dental Research: Official Publication of Indian Society for Dental Research, 31(2), 197–202. https://doi.org/10.4103/ijdr.IJDR_553_17

Murugesan, K., Anandapandian, P. A., Sharma, S. K., & Vasantha Kumar, M. (2011). Comparative Evaluation of Dimension and Surface Detail Accuracy of Models Produced by Three Different Rapid Prototype Techniques. The Journal of Indian Prosthodontic Society, 12(1), 16–20. https://doi.org/10.1007/s13191-011-0103-8

Safira, L. C., Bastos, L. C., Oliveira, T. B. de, Beal, V. E., Azevedo, R. A. de, & Sarmento, V. A. (2011). Avaliação da fidelidade de biomodelos de prototipagem rápida: estudo experimental in vivo. ImplantNews, 161–166. https://search.bvsalud.org/gim/resource/es/lil-599194

Santana, R. R., Lozada, J., Kleinman, A., Al-Ardah, A., Herford, A., & Chen, J.-W. (2012). Accuracy of Cone Beam Computerized Tomography and a Three-Dimensional Stereolithographic Model in Identifying the Anterior Loop of the Mental Nerve: A Study on Cadavers. Journal of Oral Implantology, 38(6), 668–676. https://doi.org/10.1563/aaid-joi-d-11-00130

Shahbazian, M., Jacobs, R., Wyatt, J., Willems, G., Pattijn, V., Dhoore, E., Van Lierde, C., & Vinckier, F. (2010). Accuracy and surgical feasibility of a CBCT-based stereolithographic surgical guide aiding autotransplantation of teeth: in vitro validation. Journal of Oral Rehabilitation, 37(11), 854–859. https://doi.org/10.1111/j.1365-2842.2010.02107.x

Silva, D. N., Gerhardt de Oliveira, M., Meurer, E., Meurer, M. I., Lopes da Silva, J. V., & Santa-Bárbara, A. (2008). Dimensional error in selective laser sintering and 3D-printing of models for craniomaxillary anatomy reconstruction. Journal of Cranio-Maxillofacial Surgery, 36(8), 443–449. https://doi.org/10.1016/j.jcms.2008.04.003

Singare, S., Lian, Q., Ping Wang, W., Wang, J., Liu, Y., Li, D., & Lu, B. (2009). Rapid prototyping assisted surgery planning and custom implant design. Rapid Prototyping Journal, 15(1), 19–23. https://doi.org/10.1108/13552540910925027

Taft, R. M., Kondor, S., & Grant, G. (2011). Accuracy of rapid prototype models for head and neck reconstruction. 106(6), 399–408. https://doi.org/10.1016/s0022-3913(11)60154-6

Viegas, D. M. da C. C. P., Hermínio, J. R. L., Fernandes, J. P., Arrobas, F., Roque, J. C., Mourão, J. T. C. G., & Saavedra, G. de S. F. A. (2021). Trueness and precision of the reproduction of dental casts by the conventional, milling and 3D printing techniques. Brazilian Dental Science, 24(4 suppl 1). https://doi.org/10.4322/bds.2021.e2891

Voet, V. S. D., Schnelting, G. H. M., Xu, J., Loos, K., Folkersma, R., & Jager, J. (2018). Stereolithographic 3D Printing with Renewable Acrylates. Journal of Visualized Experiments, 139. https://doi.org/10.3791/58177

Volpato N, et al. Prototipagem Rápida - Tecnologias e Aplicações. Edgard Blucher, 2007.

Descargas

Publicado

08/01/2024

Cómo citar

MARTINS, A. F. .; CÉZAR, I. E. S. .; SOARES, L. P. .; BARBOSA, M. L. G. . Evaluación del posicionamiento del canal mandibular en prototipos biomédicos estereolitográficos . Research, Society and Development, [S. l.], v. 13, n. 1, p. e4113144735, 2024. DOI: 10.33448/rsd-v13i1.44735. Disponível em: https://rsdjournal.org/index.php/rsd/article/view/44735. Acesso em: 21 nov. 2024.

Número

Vol. 13 Núm. 1

Sección

Ciencias de la salud

Licencia

Derechos de autor 2024 Andressa Ferreira Martins; Igor Ednardo Santos Cézar; Lívia Prates Soares; Maylon Luciano Garcia Barbosa

Creative Commons License

Esta obra está bajo una licencia internacional Creative Commons Atribución 4.0.

Los autores que publican en esta revista concuerdan con los siguientes términos:

1) Los autores mantienen los derechos de autor y conceden a la revista el derecho de primera publicación, con el trabajo simultáneamente licenciado bajo la Licencia Creative Commons Attribution que permite el compartir el trabajo con reconocimiento de la autoría y publicación inicial en esta revista.

2) Los autores tienen autorización para asumir contratos adicionales por separado, para distribución no exclusiva de la versión del trabajo publicada en esta revista (por ejemplo, publicar en repositorio institucional o como capítulo de libro), con reconocimiento de autoría y publicación inicial en esta revista.

3) Los autores tienen permiso y son estimulados a publicar y distribuir su trabajo en línea (por ejemplo, en repositorios institucionales o en su página personal) a cualquier punto antes o durante el proceso editorial, ya que esto puede generar cambios productivos, así como aumentar el impacto y la cita del trabajo publicado.