Comparativo de la capacidad de corte y deformación de limas de Ni-Ti tras la preparación del conducto radicular
DOI:
https://doi.org/10.33448/rsd-v12i12.43983Palabras clave:
Níquel; Titanio; Preparación del conducto radicular; Endodoncia.Resumen
Cutting capacity and deformation of nickel-titanium files were compared in simulated phenolic resin channels with 75 degrees of curvature. Twenty blocks were dried and weighed on a digital analytical balance (P0), with group A preparing the canal with type K files associated with a Hedströen file and group B using type K files. After the first use, the blocks were dried and weighed again (P1) repeating the same procedure on the second (P2), third (P3), fourth (P4) and fifth (P5) uses. Before and after five readings performed microscopically at the tip of the instruments and 5 mm from the tip with 100X, 250X and 500X (SEM JEOL JSM-5900 LV/LME-LNLS – Laboratório Nacional de Luz Sínchrotron, Campinas, SP). Each micrograph evaluated by three teachers established a score. The results demonstrated that there was no statistical difference in relation to the cutting capacity of group A compared to group B (Pvalue>0.05), the same happening between the two evaluated points of the groups (Pvalue>0.05). When comparing the two groups considering the tip of the instrument and 5 mm from it, it was statistically significant (Pvalue<0.05), that is, the average score at the tip of the instrument is higher than that 5 mm from the tip. It was concluded that there was no difference in the removal of material after preparation of the canal in Group A in relation to group B. Deformation occurred in the cutting blades of the instruments, however, without statistical significance in the two points considered in the comparison of group A with B and the average deformations at the two points of the instruments were different in the same groups.
Citas
Aasim, S. A., Mellor, A. C, & Qualtrough, A. J. E. (2006). The effects of pre-soaking and time in the ultrassonic cleaner on the cleanliness of sterilized endodontic files. Int Endod J; 37:143-149.
Alkmin, S. T., Pinto, C. A., Habitante, S. M., Zöllner, N. A., Medeiros, J. M. F., & Lage-Marques, J. L (2007). Concepção de um modelo experimental à base de resina fenólica utilizado em endodontia. In: 24ª Reunião Anual da Sociedade Brasileira de Pesquisa Odontológica; 2007; set; Atibaia. São Paulo: SBPqO
Alves-Claro, A. P. R., Claro, F. A. E., & Uzumaki E. T. (2008). Wear resistance of nickel–titanium endodontic files after surface treatment. J Materials Scie: Materials Med, 19:3273-77.
Anusavice, K. J. (2005) Phillips materiais dentários. (11a ed.), Elsevier. 337,338.
Arantes, W. B., Medeiros, J. M. F., & Lage-Marques, J. L. (2010). Evaluation of the superficial characteristics of NiTi rotary instruments before and after used. Act Report, (Laboratório Nacional de Luz Síncrotron) 1:1.
Arantes, W. B., Silva, C. M., Lage-Marques, J. L., Habitante, S. M., Rosa, L. C. L., & Medeiros, J. M. F. (2014). SEM analysis of defects and wear on Ni-Ti rotary instruments. Scanning, 36(4):411-8
Bardsley, S., Peters, C. I., & Peters, O. A. (2011). The effect of three rotational speed settings on torque and apical force with Vortex Rotary Instruments In Vitro J Endod, 37(6): 860-4.
Bergmans, L, van Cleynenbreugel, J., Wevers, M., & Lambrechts, P. (2001). Mechanical root canal preparation with NiTi rotary instruments: rational, performance and safety. Status report for the American Journal of Dentistry. Am J Dent, 14(5):324-33.
Claro, F. A. E. (2004). Avaliação do desempenho de limas endodônticas de níquel-titânio após tratamento de superfície. [Mestrado] Taubaté: Departamento de Engenharia Mecânica da Universidade de Taubaté.
Dall’Agnol, C., Hartmann, M.S.M., & Barletta, F.B. (2008). Computed tomography assessment of the efficiency of different techniques for removal of root canal filling material. Braz Dent J, 19(4):306-12.
Fariniuk, L. F., Azevedo, M. A. D., Carneiro, E., Westphalen, V. P. D., Piasecki, L., & Silva Neto, UX. (2017). Efficacy of protaper instruments during endodontic retreatment. Indian J Dent Res, 28(4):400-405.
Gambarini, G., Grande, N. M., Plotino, G., Somma, F., Garala, M., Luca, M., & Testarelli, L. (2008). Fatigue Resistance of Engine-driven Rotary Nickel-Titanium Instruments Produced by New Manufacturing Methods. J Endod, 34(8):1003-5.
Gavini, G., Santos, M. D., Caldeira, C. L., Machado, M. E. L., Freire, L. G., Iglecias, E. F., Peters, O. A., & Candeiro G. T. M. (2018). Nickel-titanium instruments in endodontics: a concise review of the state of the art. Braz Oral Res,18(32), e67,
Hartmann, M. S., Barletta, F. B., Camargo Fontanella, V. R., & Vanni, J. R. (2007). Canal transportation after root canal instrumentation: a comparative study with computed tomography. J Endod, 33(8):962-5.
Kazemi, R. B., Stenman, E., & Spangberg, L. S. W. (1996). Maching efficiency and wear resistance of nickel-titanium endodontic files. Oral Surg Oral Med Oral Pathol Oral Radiol Endod, 81(5):596-602.
Kosa, D. A., Marshall, G., & Baumgartner, J. C. (1999). An analysis of canal centering using mechanical instrumentation techniques. J Endod, 25(6):441-5.
Medeiros, J. M. F., Arantes, W. B., Rosa, L. C. L., Haddad Filho, M. S., Zöllner, N. A., & Habitante, S. M. (2019). Microscopia eletrônica de varredura da presença de resíduos na superfície de corte de instrumentos NITI. Rev Odontol Univ Cidade São Paulo (Online), 31(2):116-24.
Medeiros, J. M. F., Ferreira, G. S., Lima, K. C., Pedron, I. G., & Shitsuka, C. (2022a). Comparativo de dois protocolos de substâncias químicas auxiliares utilizados em endodontia em duas faculdades de odontologia (USP-São Paulo e UNICAMP-Piracicaba). e-Acadêmica, 3(3):e3833242-253.
Medeiros, J. M. F., Lima, J. P., & Bombana, A. C. (2002). Analysis by scanning electron micoroscopy of the cutting surface changes on endodontics files according two methods for sterilizing and the number of uses. Act Report, 1:267-268.
Medeiros, J. M. F, Naregi, E. S., Almeida, E. T. D. C., Von Dollinger, C. F. A., Rosa, L. C. L., Haddad Filho, M. S., & Forghieri, A. A. (2014). Medidas de dureza vickers na superfície de blocos de resina fenólica com canais endodônticos simulados. Publicatio UEPG. Ci Biol Saúde (Online), 20(1):53-71.
Medeiros, J. M. F., Rodrigues, G. A., Santos, A. C. M., Rosa, L. C. L., Carvalho, P. L., & Nohara, E. L. (2009). Determinação do comprimento e grau de curvatura em canais radiculares curvos simulados confeccionados em blocos de resina fenólica. Rev Odontol Univ Cidade de São Paulo, 21(3):202-11.
Medeiros, J. M. F., Souza, A. P. B. R., Sakane, F. K., Rosa, L. C. L., Carvalho, P. L., Claro, A. P. R. A., & Pedron, I. G. (2022b). Comparative Study of Cutting Capacity and Wear in 3 Commercial Brands of Ni-Ti Manual Endodontic Files. SVOA Dentistry, 3(5), 235-242.
Morrison, S. W., Newton, C. W., & Brown Jr, C. E. (1989). The effects of steam sterilization and usage on cutting efficiency of endodontic instruments. J Endod, 15(9):427-31.
Pécora, J. D. (2004). Peculiaridades, Cinemática e Uso dos Instrumentos de Pega Digital. Atualizado 27/06/2004. https://www.forp.usp.br/restauradora/endodontia/temas/instrumental/instrumental_dig_pec.pdf
Reis, P. S. C. (2022). Protocolo clínico dos sistemas de limas mecanizadas Recioproc Blue e Trunatomy. 2022. 48 f. il. Monografia (Especialização) -- Universidade Federal de Minas Gerais, Faculdade de Odontologia.
Reis, P. R. B., Lage-Marques, J. L., Habitante, S. M., Rosa, L. C. L., & Medeiros, J. M. F. (2011). Avaliação in vitro da capacidade de corte e deformação de limas rotatórias de níquel-titânio. Rev ClipeOdontol, 3(1):19-27.
Schäfer, E., & Tepel, J. (1996). Cutting efficiency of Hedstrom, S and U files made of various alloys in filing motion. Int Endod J, 29(5):302-8.
Shen Y, & Haapasalo M. (2008). Three-dimensional analysis of cutting behavior of nickel-titanium rotary instruments by microcomputed tomography. J Endod, 34(5):606-10.
Svec, T. A., & Powers, J. M. (2002). The deterioration of rotary nickel-titanium files under controlled conditions. J Endod, 28(2): 105-7.
Tepel, J., & Schäfer, E. (1997). Endodontic hand instruments: cutting efficiency, instrumentation of curved canals, bending and torsional properties. Endod Dent Traumatol, 13(5):201-10.
Troian, C. H., Sá, M. V. R., Figueiredo, J. A. P., & Oliveira, E. P. M. (2006). Deformation and fracture of RaCe and K3 endodontic instruments according to the number of uses. Int Endod J, 39(8):616–25.
Wagner, M. H., Barletta, F. B., Reis, M. S., Mello, L. L., Ferreira, R., & Fernandes, A. L. R. (2006). NSK reciprocating handpiece: In vitro comparative analysis of dentinal removal during root canal preparation by different operators. Braz Dent J. 17(1):10-4.
Yang, X., Wang, Y., Ji, M., Li, Y., Wang, H., Luo, T., Gao, Y., & Zou, L. (2023). Microcomputed tomographic analysis of the efficiency of two retreatment techniques in removing root canal filling materials from mandibular incisors. Sci Rep, 13(1):2267.
Weine, F. S. (1982). Endodontic therapy. Third Edition. Mosby. 259, 262.
Zangh, E. W., Cheung, G. S., & Zheng, Y. F. (2010). Influence of cross-sectional design and dimension on mechanical behavior of nickel-titanium instruments under torsion and bending: a numerical analysis. J Endod, 36(8):1394-8.
Descargas
Publicado
Cómo citar
Número
Sección
Licencia
Derechos de autor 2023 João Marcelo Ferreira de Medeiros; Thyssiane de Macedo Mansano; Luiz Carlos Laureano da Rosa; Miguel Simão Haddad Filho; Pedro Luiz de Carvalho; Caleb Shitsuka; Irineu Gregnanin Pedron
Esta obra está bajo una licencia internacional Creative Commons Atribución 4.0.
Los autores que publican en esta revista concuerdan con los siguientes términos:
1) Los autores mantienen los derechos de autor y conceden a la revista el derecho de primera publicación, con el trabajo simultáneamente licenciado bajo la Licencia Creative Commons Attribution que permite el compartir el trabajo con reconocimiento de la autoría y publicación inicial en esta revista.
2) Los autores tienen autorización para asumir contratos adicionales por separado, para distribución no exclusiva de la versión del trabajo publicada en esta revista (por ejemplo, publicar en repositorio institucional o como capítulo de libro), con reconocimiento de autoría y publicación inicial en esta revista.
3) Los autores tienen permiso y son estimulados a publicar y distribuir su trabajo en línea (por ejemplo, en repositorios institucionales o en su página personal) a cualquier punto antes o durante el proceso editorial, ya que esto puede generar cambios productivos, así como aumentar el impacto y la cita del trabajo publicado.
